Co2 Inflators

For safety reasons, we recommend not screwing the CO2 cartridge into the inflator head until needed in order to prevent CO2 being dispensed in storage / transport.
One you have achieved the required tyre pressure, any residual gas in the cartridge should be fully emptied for safety reasons.
Most threadless presta valves have a small screw / threaded section at the very top of the valve stem which normally works with our CO2 inflator. If you purchase the inflator and things aren’t compatible for some reason, then send us a message and we’ll ensure we make things right for you.
The CO2 inflator is compatible with both Presta and Schrader valves, as the force of the gas expelled from the inflator head forces the valve open, no matter which type it is.
Yes, however you will need to ensure that the removable element is fully screwed into the valve so that it does not become loose under the pressure of the gas and potentially waste any of the content of your cartridge.
The tyre pressure that you can achieve with the inflator depends on what size cartridge you use, and the type of tyre that you have. Please refer to the below chart to find out what pressures can be achieved. Please bear in mind that CO2 gas slowly dissipates through rubber over time. As such, you will find that the normal tyre pressure will reduce slightly in the following day as the gas dissipates. We therefore recommend you refill your tyres with normal air using a conventional bike pump (mini or floor) once you get home after your ride.
The CO2 inflator head supplied with the red foam sleeve fits ANY size of threaded CO2 cartridge (12g, 16g, 20g & 25g). However, please be aware that the red foam sleeve is designed to only fit over a 16g threaded CO2 cartridge. The CO2 inflator with metal storage canister is designed for 12g or 16g threaded CO2 cartridges, both can be stored in the storage canister before or after use.
A spare o-ring is a potential replacement for both of the o-rings that are inside the inflator (the one in the nozzle that connects to the tyre valve, and the one in the end that you screw the co2 cartridge into). If either of the current ones wears out or falls out for some reason, you just need to insert the new one. You will need to poke it down into the relevant end of the inflator to position it.

Bottle Cages

The bottle cage will fit the vast majority of bike water bottles, from 500ml (18oz) to 1000ml (35oz). If you’re finding it’s too tight or too loose, you can adjust the wings of the bottle cage to accommodate. Just pull apart or push in the wings; the bottle cage is designed to be able to flex slightly.
If the supplied bolts do not fit, the bike itself should have come with bolts in the frame holes, which will fit.

Bicycle Pumps

The hose and gauge are stored within the pump itself. You can access this by lifting the cap at the handle end of the pump and pulling out the hose within. You then screw the relevant end of the hose into the body of the pump and it is then ready to use.
The frame of your bicycle will need pre-drilled holes in the frame, and there should be bolts screwed into these holes. To install the bracket, ensure the threads on the mounting bolts are clean of debris, paint and metal chips, and then put a thin film of grease on them. You then line up the bracket with the holes, and hand tighten the bolts using a screwdriver or allan key, whichever is relevant. Be careful not to cross thread the bolts!
Yes, however you will need to ensure that the removable element is fully screwed into the valve so that it does not twist and come loose when you screw the pump hose onto the valve. If this does not work, you could also consider superglueing the core into the valve.
You need to ensure that the Presta valves are fully open, and then screw the hose valve head DEEPLY onto the tyre valve. This creates a full seal, allowing all the air to be pushed through when pumping. If a full seal is not created, then the air will sometimes get trapped in the pump. This will cause a ‘backup’ of air making pumping difficult, and in some cases the pump will heat up as the air has nowhere to go.

Mini Ratchet Toolset

Yes the handle can be used directly with the tool bits, without the extender
The case is: 3.9 inches long, 3.1 inches wide and 1 inch deep

Torque Wrench Set 2-20Nm

Pro Bike Tool is pleased to offer a lifetime warranty against manufacturer defects. If your product has a manufacturing defect in materials or workmanship, we will repair or replace it, without charge. For a product that is no longer in production or in stock, and cannot be repaired, a replacement with a comparable Pro Bike Tool product or a full refund will be offered instead. Issues not covered under warranty: Normal wear and tear Improper installation Damage or failure due to heat, accident, misuse, abuse or neglect. The warranty is void in its entirety by any modification or dismantling of the warranted product. This warranty extends from the date of purchase, applies to the original owner and is not transferable.

Adjustable Torque Wrench

Yes, this adjustable torque wrench is designed to be used to tighten bolts on a carbon frame bike. The torque wrench has torque settings of 4, 5 & 6Nm which covers most bolts on your bike. For carbon frame bikes, there should be a label near the bolt informing you of the Nm setting to use.
We recommend setting it to the lowest setting when not in use

Chain Tool

Yes, the chain tool can be used with a single speed chain.
The chain tool is manufactured in Taiwan

Chain Pliers

Yes, the chain pliers will work with a Shimano quick-link chain.

6-in-1 Y Wrench

The tool bits are longer and double-ended than normal tool bits, the material used for these tool bits is very hard, heat treated S2 steel. You can use normal tool bits; however, they’ll be slightly short when inserted into each tool shaft, but they’ll work.

Allen Key Set

The Allen Key Set is manufactured in Taiwan.

8-in-1 Multitool

The PRO BIKE TOOL multitool is made from cold forged SUS420 stainless steel for high strength and durability.
The multitool includes the following: Allen / Hex Tool 2.5/3/4/5/6, Star Shaped/Hex Tool T25/T30 and Phillips Tool PH1 cross drive.
The multitool does not have a flathead screwdriver, however, it includes the following: Allen / Hex Tool 2.5/3/4/5/6, Star Shaped/Hex Tool T25/T30 and Phillips Tool PH1 cross drive.

Bike Covers

XXL SIZE FOR 2-3 BIKES – 82 L x 44 H x 44 W inches (208 x 112 x 112 cm)
EXTRA LARGE SIZE FOR 1-2 BIKES – Generous size 82 L x 44 H x 30 W inches (208 x 112 x 76 cm).
LARGE SIZE FOR 1 BIKE – Generous large size 77 L x 39 H x 25.5 W inches (195 x 100 x 70 cm).
If using a ‘hitch mounted bike rack’ on the back of an RV, truck or car we recommend to ‘SIZE-UP’ as bikes on a rack are positioned apart and in opposite directions – if storing 2 bikes, we recommend our ‘XXL’ size cover.